LOAD BEARING PLATES
Load bearing plates are used where the angle of installation is perpendicular to the structure or application. They are available in galvanised steel and stainless steel in the following standard sizes - 100mm sq., 150mm sq., 200mm sq. and 300mm sq.
In addition, polyethylene load plates are also available. Generally associated with lightweight geotextile applications this type of plate bears only a nominal load to the geotextile to hold it in position. Polyethylene plates are available in 90mm Ø, 150mm sq. and 200mm sq. as standard.
Different sizes of load bearing plates can be made to order to suit specific customer requirements.
 |
Download it Here | |
 |
DOWNLOAD
FLASH PLAYER HERE |
|
 |
 |
 |
||||||||||||||
|
||||||||||||||||
|
||||||||||||||
| SELF ALIGNING INVERTED PATRESS PLATES | ||||||||||||||
 |
||||||||||||||
 |
||||||||||||||
| Designed
with a recess and plastic cover, allowing the wedge grip and wire tendon
to be completely concealed with minimum projection from the structure. A
hemi-spherical ball situated in the recess allows the angle of installation
to vary between 0°-30° from horizontal.
This top accessory is used mostly for projects where the finished
appearance |
||||||||||||||
| DISHED PLATE | ||||||||||||||
 |
||||||||||||||
 |
||||||||||||||
| The dished plate
is used on projects where the plate is not perpendicular to the wire tendon
and aesthetic appearance is not as important. The elongated hole, shallow
recess and hemi-spherical ball allows the angle of installation to vary
between 0° - 20°. Dished plates are available in galvanised steel
or stainless steel in the same standard sizes as the load bearing plate. |
||||||||||||||
| DISHED REVETMENT PLATES | ||||||||||||||
 |
 |
|||||||||||||
|
The dished revetment plate is a top accessory developed to fit most standard revetment blocks. It is designed to sit in the cavity of the revetment block
and allows the conical grip and wire tendon to finish flush or below the
block’s surface. Available as standard in stainless steel in the
following sizes – 100mm x 135mm and 135mm |
||||||||||||||
| TENSIONER | ||||||||||||||
 |
||||||||||||||
 |
||||||||||||||
| The tensioner
is associated with pipeline earth anchor systems where buoyancy control is a major problem. It is used to tension the anchor systems installed either
side of the pipeline and prevents any further movement. Produced in galvanised
steel and stainless steel it is used with a webbing strap.
|
||||||||||||||
| THE TURNBUCKLE | ||||||||||||||
 |
 |
|||||||||||||
| The turnbuckle
is used in guyed applications. It is connected to the anchor system using
a hard eye top termination.
Once the earth anchor system has been loadlocked and the turnbuckle
has been fully extended it is connected to the guy wire of the structure.
Final adjustment can be made by rotating the main body of the turnbuckle
and retracting each end. Of galvanised steel construction, it accepts
wire tendon Ø up to 12mm as standard. Other sizes and materials
are also available. |
||||||||||||||
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
||
|
 |
|
Platipus
Anchors Limited - UK Office Kingsfield Business Centre, Philanthropic
Road, REDHILL, Surrey, RH1 4DP, England. Tel: +44 (0) 1737 762300 Fax: +44 (0) 1737 773395 Email: info@platipus-anchors.com |
|
|||
|
|||
|
|||
|
 |
|
Platipus
Anchors Inc - USA Office 2008 Garner Station Boulevard, Raleigh, NC
27603, USA.
Tel: 866 PLATIPUS (752 8478) Fax: 919 859 9597 Email: info@platipus-anchors.com |
|
|||
